The first description will create a bond that you could most likely pass on to your great-grandchildren. The second one may not last that long, but I know of one made of mild steel that has never been quenched or tempered. It has been used to fire over 5,000 rounds and is still solid. All that`s wrong is that the part that the bolt holder hits is illuminated after about five or six hundred shots. When this happens, the girl who owns it drops it from the gun, places it on the rear bumper of the Jeep hBr and puts it back in shape with a stone. She is then back in business for a few hundred more rounds. Yes. The KNS Precision Lightning Link Re-Enforcer fits the AR15 platform, including your M&P. When properly installed and used on a repairable Lightning Link, the weak area of the connection is strengthened. During installation, it may be necessary to remove the .040″ material from the bottom of the top receiver disassembly pin and a small amount from the back of the hammer. In operation, the dismantling pin post acts as a pivot point.
When the bolt holder hits the links vertically, the Icwer end is shaken backwards, moving the limb body 1/15 inch back, releasing the hammer under the division hook. A3 As long as the trigger is retained, the backward movement of the bolt tightens the hammer under the separator hook. The forward movement of the wearer hits the limb post, just as the bolt falls into place, releases the hammer and fires the weapon. When the trigger is released, the shutter stops the hammer in the taut position, cancelling the function of the circuit breaker and flash connection. THIS IS NOT AN ITEM REGISTERED BY THE NFA AND DOES NOT TURN YOUR RIFLE INTO A MACHINE GUN This new product, when properly installed and used on a repairable Lightning Link, strengthens the weak area of the connection. Installation may require removal of .040 material from the bottom of the top receiver removal pin and a small amount from the back of the hammer. The installation and use of this amplifier does not imply or imply or expressly express any liability, warranty or warranty to the manufacturer or seller to cover the cost or value of the firearm, firearm accessories or flash connection in the event of an accident, loss or breakage of any kind. The Bureau of Alcohol Tobacco Firearms and Explosives has approved the use of this product on Lightning Links legally registered under the National Firearms Act (NFA). HOWEVER, USING THIS REINFORCEMENT PIECE TO REPLACE PART OF A FAULTY REGISTERED LIGHTNING CONNECTION WOULD CONSTITUTE THE MANUFACTURE OF A NEW, UNREGISTERED MACHINE GUN AND VIOLATE THE NFA. (Judgment #903050:MRC 3311/2005-474) Detailed instructions and helpful tips included. The mounted link sits flat in the lower receiver, with the opening at the front fitting on the circuit breaker hook and the post resting vertically between the receiver`s top retract pin post and the bolt bracket. The only complaint I`ve ever heard about the Lightning Link is that it only converts the gun to fully automatic.
I do not see how that is a problem. No one is saying that you have to press the shutter button and hold it down until the charger is empty. I`ve found that with a little practice, it`s easy to shoot two shots with the link. The Lightning connection allows for fully automatic firing by pulling the disconnector back and forcing it to release the hammer. On the other hand, if you use just a few pieces of hacksaw blade to make the parts, a Dremel tool, a hand drill, and a file or two to get the job done, you can cut the «Lightning Link» in about an hour. As long as the trigger is retained, the shutter(s) is held under the arch of the hammer notch. The only thing that keeps the hammer in the taut position is the circuit breaker. In normal semi-automatic operation, the hammer is stretched by a backward movement of the bolt holder, when the beam advances, the hammer is caught and held in the taut position by the seam located on the front part of the trigger stuck in the notch of the shutter on the hammer. If you hold the trigger down after a shot has been fired, the sealant will not get stuck in the hammer attachment notch when the hammer accumulates, as the sealant will be pressed under the arch of the hammer notch.
The parts can be made of tool steel, machined with high precision, tempered and tempered with love, and then polished to a high gloss that your mother would be proud of. This thing is as smooth as owls! do! Don`t worry about M-16 parts. No machining or drilling on a six-hundred-dollar gun. Also note that it takes about ten seconds to install the Lightning Link in an unchanged standard AR-15. and only about six «seconds» to remove it.
